Hi Anas,

Copy the File into this Folder and then Reboot the Device.

When you put an Full or Incremental Update Package or an APK file in this "Autoinstall" folder you must only reboot the Device.

After Rebooting is the Scanner installing / executiong the files in this Folder.

It works ;)

Hi Anas,

Thank you for posting on SOTI Central.

Could you please provide some more information about the device such as method of enrollment, Agent version and the details under Device Information -> 'Supported APIs'.

Many thanks,

Hello , 

Hi Anas,

Thanks for the information.

Please try the below script, if successful then you can use it as a post-install script in your File Sync Rule. However, there is a chance it won't work if the device is encrypted:

install_system_update /sdcard/honeywell/autoinstall/filename.zip

Otherwise you can try the sendintent command: The sendintent Command (soti.net)

Kind regards,

Hi Anas,

Make sure the original filename of the HON updates is unchanged. You can initiate the update using the intent below: 

sendintent -b "intent:#Intent;action=com.honeywell.autoinstall.intent.action.INSTALL;S.InstallFiles=/storage/emulated/0/honeywell/HON660-O-86.00.17-(0129)_86.00.19-(0140).zip;launchFlags=0x1400020;end"

Or initiate a reboot with "reset /S" so that the upgrade is initiated by Autoinstall upon startup. 

Good luck! 

Hi Anas,

Thanks for the information.

Please try the below script, if successful then you can use it as a post-install script in your File Sync Rule. However, there is a chance it won't work if the device is encrypted:

install_system_update /sdcard/honeywell/autoinstall/filename.zip

Otherwise you can try the sendintent command: The sendintent Command (soti.net)

Kind regards,

Are you sure about this? As far as I'm aware the install_system_update script was for executing .ZIP updates on Zebra devices, and not Honeywell. Has the script been updated in order to dynamically support different manufacturers?

Hi Matt,

Good question, I understand this script has worked on some Honeywell and Panasonic devices in the past. Otherwise, the sendintent command should suffice.

Kind regards,

Hello All, 

Hello, 

Both files are already in the autoistall folder but after a reboot nothing happen .

Best regards.

Hi Anas,

can yu add the following Points

- What Honeywell Device Type you are trying to Update

- What Android Version is Installed with Patchlevel is installed -> example 86.00.26-(0185)

Next Point, what Packages are you trying to install in the Autoinstall folder ?

Hello, 
Im trying to update CK75 devices (Short and long range) with both GMS ana NONGMS versions .

The already existing OEM versiob are 81.01.10-(0090) / 81.01.08-(0077) / 82.01.10-(0090) /82.01.08-(0077) and all of then i need to upgrade them to the verion 82.01.12-(0110) / 81.01.12-(0110)

Best regards.

Hi,

that is intersting.

At the non GMS Device with the installed Android Version 81.01.10-(0090) / 81.01.08-(0077) and you put the PHOENIX-M-sd-81.01.12-(0110).zip into the Autoinstall Folder and reboot or check if you are able to install the Update with the Hoenywell app at the Device ?

Hello, 
I already tested that but its not working and now i m getting a message that there is no package  to upgrade and its not the case  when i run the The sendintent Command 

Hello All ,

Now its working  after Moving all needed file in Internal storage/iPSM/honeywell/autoinstall instead of sdcard. 

Also the update is ruunnig just withou any script , all you need to to is to restart your device . 

Thank you all .

Hi Anas 

Glad to hear that provided solutions worked for you. 

I would request you to mark the particular comment as "is solution", so others may benefit from this information.